Forks

Legends Never Die Back in a big way, the all-new Dorado Pro is ready to turn the suspension world upside down. Featuring an inverted design, carbon upper structure, 37mm stanchions, and refreshed internals the new Dorado Pro is the pinnacle of suspension technology. The new stiffer chassis is paired with an all-new sealed version of our TPC+ damper and improved Dorado Air Spring with an IRT volume adjuster. These technologies combined into one ultimate platform provide more than enough tunability to satisfy any savvy suspension tuner while being so easy to adjust that every rider can dial in their fork with ease. Key Features: - Carbon Fiber Legs and the 37mm chassis result in the stiffest and lightest Dorado to date. The carbon pro chassis is 27% stiffer than the previous 36mm version and 238g lighter than the new 37mm Expert version. They also have looks that can kill. - Inverted Design provides an incredibly smooth and consistent feel due to constant lubrication of the bushings and seals. The inverted design also provides a major increase in fore-aft stiffness compared to traditional forks while maintaining torsional compliance which provides more control to the rider over rough terrain. - Dorado Air Spring system contains a unique balancing valve that equalizes the positive and negative air chambers during the air-fill process resulting in a consistent feel without any flat or dead spots. It also allows easy Travel Adjustability from 180 to 190 and 203mm without the need for any spare parts. - IRT (Infinite Rate Tune) allows for advanced spring tuning by independently adjusting air pressures in the beginning and end stroke. IRT technology creates a secondary positive air spring that affects only the middle-to-end stroke of the fork. This allows the main air spring to be set to lower pressures for improved small bump sensitivity while maintaining mid-stroke support and moderate to aggressive end-stroke ramp-up. - Sealed TPC+ is a velocity and position-dependent damping circuit that maintains light damping through small bumps when the fork is high in its travel. As the fork compresses deeper in the travel the secondary TPC+ circuit engages and increases the damping force for added support and bottom-out prevention. Additionally, an independent Hydraulic Bottom-out circuit further increases the damping force in the final 30mm of travel to soften deep travel events and prevent hard bottom-out. The new cartridge design with spring-backed IFP fully seals damper oil for the most consistent damping on long demanding DH runs. Spring-backed IFP has improved performance during extreme riding, unlike a bladder an IFP pressurizes the oil at the initial stroke eliminating any cavitation for the most consistent damping. - Fits both 29" and 27.5" wheels. Markings on the outer legs indicate the proper clamping point for the ideal axle to crown measurements depending on wheel size. The fork legs can be used with both wheel sizes. - Two Crown Options are available with this fork. The 47 offset is designed to work with 27.5" wheels and intended axle to crown. The 57 offset crown is designed for 29" wheels and axle to crown. For those looking to run the lower offset crown with 29" wheels please reference our fit document to see if your headtube length is compatible. - TSR Bleed buttons allow you to release excess pressures built up in the outer legs of your fork with a simple tap of the button. This keeps your fork smooth and supple all day long. Product Details: - 37mm 6000 Series Aluminum stanchions with carbon fiber legs - Externally Adjustable: high-speed compression, low-speed compression, and rebound - Dorado air spring with IRT (Infinite Rate Tune) volume adjuster allows the rider to adjust mid-stroke support and bottom-out progressivity independent of initial spring rate - TPC+ Damper with HBO (Hydraulic Bottom Out) - TSR Bleeders - Includes removable bolt-on fender

More than 20 years ago, BoXXer changed the DH world when it hit the scene. Featuring Charger 2.1 damper for unrivaled control between the tape. Ultra-low friction SKF wiper seals and race-proven Maxima Plush damping fluid all work overtime to reduce friction, noise, and provide lasting fork performance all the way to the finish corral. - Completely re-designed to reduce hand fatigue and fight unwanted friction, the Charger 2.1 damper increases confidence and control over every trail - Charger 2.1 RC2 damper featuring independent high- and low-speed compression adjust - Highly tunable DH-specific DebonAir spring offers a coil-like consistent feel throughout the travel - Ultra-low friction SKF wiper seals provide long-lasting fork performance and improve overall suspension feel - Maxima Plush damping fluid reduces friction and silences damper noise - Ultimate foil graphics package

Coil Fans Rejoice! Once again, the Dorado is available with a coil option. The new Dorado Comp features the same 37mm chassis as the Expert but with a more set-it-and-forget-it vibe. The coil spring provides a smooth consistent feel 100% of the time with 0% of any hassle. On the damping side of things, our ABS+ Damper offers a great adjustment range, terrific reliability, and easy serviceability. The Dorado Comp is built for riders who just want to ride and not sweat any of the small stuff. Key Features: - New 37mm chassis results in a massive increase in stiffness and ride quality. The new chassis is 20% stiffer compared to our former 36mm version. - Inverted Design provides an incredibly smooth and consistent feel due to constant lubrication of the bushings and seals. The inverted design also provides a major increase in fore-aft stiffness compared to traditional forks while maintaining torsional compliance which provides more control to the rider over rough terrain. - Coil Spring provides maximum bump sensitivity and simple service procedures. The standard spring rate provided in the fork is a medium rate of 35lb/in. For tuning, there are six spring rates available for this fork; 25lb/in, 30lb/in, 35lb/in, 40lb/in, 45lb/in, and 50lb/in. - ABS+ damper is known for its incredible reliability and easy tunability. Adjustments include a low-speed compression adjustment and a low-speed rebound adjustment. - Fits both 29" and 27.5" wheels. Markings on the outer legs indicate the proper clamping point for the ideal axle to crown measurements depending on wheel size. The fork legs can be used with both wheel sizes. - Two Crown Options are available with this fork. The 47 offset is designed to work with 27.5" wheels and intended axle to crown. The 57 offset crown is designed for 29" wheels and axle to crown. For those looking to run the lower offset crown with 29" wheels please reference our fit document to see if your headtube length is compatible. - TSR Bleed Screws allow you to release excess pressures built up in the outer legs of your fork while riding keeping your fork smooth and supple all day long. Product Details: - 37mm 6000 Series Aluminum stanchions with carbon fiber legs - Externally Adjustable: high-speed compression, low-speed compression, and rebound - Dorado air spring with IRT (Infinite Rate Tune) volume adjuster allows the rider to adjust mid-stroke support and bottom-out progressivity independent of initial spring rate - TPC+ Damper with HBO (Hydraulic Bottom Out) - TSR Bleeders - Includes removable bolt-on fender

E-Bike specific long-travel Enduro fork with 38mm stanchion tubes featuring, floating axle, new arch design, and lower leg bleeders to release built-up pressure. - Genuine Kashima Coating on upper tubes - GRIP2 damper with Variable Valve Control - Next generation FLOAT EVOL with larger negative air chamber increases small bump sensitivity - Floating axle design - Lower leg bleeders - Direct mud guard mount

FOX 38 Factory Series Suspension Fork is the long-travel enduro specialist. It redefines what you think a long travel single crown fork is capable of, and sets a new benchmark for confidence, performance, and durability. - The floating axle offers a distinct performance advantage due to its unique ability to match the exact width of the fork’s wheel mounting surface precisely to the front hub flange spacing, thus creating perfect chassis alignment and eliminating unwanted friction between the upper and lower fork legs - Floating axles provide much smoother suspension movement throughout the entire range of the fork’s travel, notably improving sensitivity and overall ride quality - The 38 Fork comes equipped with a quick-release lever operated patent-pending floating axle system, combining the benefit of a floating axle with the ease of a tool-free quick-release - Lower leg bypass channels alleviates air pressure by dramatically increasing air volume within the lower legs and thereby reducing the amount of additional unintended pressure ramping - Lower leg bleeders allow for atmospheric pressure equalization at the simple press of a button - The 38's lower leg arch design pulls out all the stops, shaving every possible gram while making sure not to compromise stiffness or strength requirements of modern enduro and gravity style riding

FOX 38 Factory Series Suspension Fork is the long-travel enduro specialist. It redefines what you think a long travel single crown fork is capable of, and sets a new benchmark for confidence, performance, and durability. - The floating axle offers a distinct performance advantage due to its unique ability to match the exact width of the fork’s wheel mounting surface precisely to the front hub flange spacing, thus creating perfect chassis alignment and eliminating unwanted friction between the upper and lower fork legs - Floating axles provide much smoother suspension movement throughout the entire range of the fork’s travel, notably improving sensitivity and overall ride quality - The 38 Fork comes equipped with a quick-release lever operated patent-pending floating axle system, combining the benefit of a floating axle with the ease of a tool-free quick-release - Lower leg bypass channels alleviates air pressure by dramatically increasing air volume within the lower legs and thereby reducing the amount of additional unintended pressure ramping - Lower leg bleeders allow for atmospheric pressure equalization at the simple press of a button - The 38's lower leg arch design pulls out all the stops, shaving every possible gram while making sure not to compromise stiffness or strength requirements of modern enduro and gravity style riding

FOX 38 Factory Series Suspension Fork is the long-travel enduro specialist. It redefines what you think a long travel single crown fork is capable of, and sets a new benchmark for confidence, performance, and durability. - The floating axle offers a distinct performance advantage due to its unique ability to match the exact width of the fork’s wheel mounting surface precisely to the front hub flange spacing, thus creating perfect chassis alignment and eliminating unwanted friction between the upper and lower fork legs - Floating axles provide much smoother suspension movement throughout the entire range of the fork’s travel, notably improving sensitivity and overall ride quality - The 38 Fork comes equipped with a quick-release lever operated patent-pending floating axle system, combining the benefit of a floating axle with the ease of a tool-free quick-release - Lower leg bypass channels alleviates air pressure by dramatically increasing air volume within the lower legs and thereby reducing the amount of additional unintended pressure ramping - Lower leg bleeders allow for atmospheric pressure equalization at the simple press of a button - The 38's lower leg arch design pulls out all the stops, shaving every possible gram while making sure not to compromise stiffness or strength requirements of modern enduro and gravity style riding - GRIP2 damper includes Fox's patented Variable Valve Control (VVC) technology which allows for external fine-tuning of suspension performance - FLOAT EVOL air spring technology increases negative air spring volume, optimizing small bump sensitivity - Direct mud guard mount - Genuine Kashima Coating on upper tubes - 27.5: 723mm peak tire diameter

Coil Fans Rejoice! Once again, the Dorado is available with a coil option. The new Dorado Comp features the same 37mm chassis as the Expert but with a more set-it-and-forget-it vibe. The coil spring provides a smooth consistent feel 100% of the time with 0% of any hassle. On the damping side of things, our ABS+ Damper offers a great adjustment range, terrific reliability, and easy serviceability. The Dorado Comp is built for riders who just want to ride and not sweat any of the small stuff. Key Features: - New 37mm chassis results in a massive increase in stiffness and ride quality. The new chassis is 20% stiffer compared to our former 36mm version. - Inverted Design provides an incredibly smooth and consistent feel due to constant lubrication of the bushings and seals. The inverted design also provides a major increase in fore-aft stiffness compared to traditional forks while maintaining torsional compliance which provides more control to the rider over rough terrain. - Coil Spring provides maximum bump sensitivity and simple service procedures. The standard spring rate provided in the fork is a medium rate of 35lb/in. For tuning, there are six spring rates available for this fork; 25lb/in, 30lb/in, 35lb/in, 40lb/in, 45lb/in, and 50lb/in. - ABS+ damper is known for its incredible reliability and easy tunability. Adjustments include a low-speed compression adjustment and a low-speed rebound adjustment. - Fits both 29" and 27.5" wheels. Markings on the outer legs indicate the proper clamping point for the ideal axle-to-crown measurements depending on wheel size. The fork legs can be used with both wheel sizes. - Two Crown Options are available with this fork. The 47 offset is designed to work with 27.5" wheels and intended axle to crown. The 57 offset crown is designed for 29" wheels and axle to crown. For those looking to run the lower offset crown with 29" wheels please reference our fit document to see if your headtube length is compatible. - TSR Bleed Screws allow you to release excess pressures built up in the outer legs of your fork while riding keeping your fork smooth and supple all day long. Product Details: - 37mm 6000 Series Aluminum stanchions with aluminum legs - Externally adjustable low-speed compression spring preload and rebound - Includes removable bolt-on fender - 2.6 max tire width - 223mm max rotor diameter

- 38mm chassis for increased stiffness and rider confidence - ButterCups block 20% of high frequency "trail chatter". Limiting these vibrations massively reduces hand and arm fatigue leaving you feeling fresh with more control. - Charger 3 features a completely new Internal Floating Piston (IFP) design with better fidelity, performance and truly independent adjustments without any "cross talk". - DebonAir+ is built to strike the perfect balance of what riders really want: butter-like small bump feel, increased air volume, and higher overall ride height. - Ultimate Bushing Package maximizes the fork's bushing overlap, reducing friction and creating the smoothest ride possible - Pressure Relief Valves eliminate unwanted air pressure build up in the lower leg caused by variations in altitude or temperature - Includes premium short fender

Get Inverted Back and better than ever the new Dorado Expert is ready to take on the gnarliest conditions mountain biking can provide. Whether you’re looking to cut seconds off the splits, lap the local park, or get sendy in the back hills of Utah the Dorado Expert has you covered. Featuring an all-new 37mm chassis, completely redesigned internals, and on-trail precision that only inverted forks can provide the new Dorado is your ticket to the best ride you’ve ever had. Key Features: - New 37mm chassis results in a massive increase in stiffness and ride quality. The new chassis is 20% stiffer compared to our former 36mm version - Inverted Design provides an incredibly smooth and consistent feel due to constant lubrication of the bushings and seals. The inverted design also provides a major increase in fore-aft stiffness compared to traditional forks while maintaining torsional compliance which provides more control to the rider over rough terrain. - Dorado Air Spring system contains a unique balancing valve that equalizes the positive and negative air chambers during the air-fill process resulting in a consistent feel without any flat or dead spots. It also allows easy Travel Adjustability from 180 to 190 and 203mm without the need for any spare parts. - IVA (Incremental Volume Adjust) modifies the volume in the positive air chamber with self-contained spacers dictating the position of the IVA piston and your volume amount. - New TPC+ Damper has increased oil volume and improved flow paths for improved bump compliance and increased consistency. TPC+ features two compression pistons, a hydraulic bottom out, and a spring-backed IFP for a smooth and predictable feel for every impact. Adjustments include; High-speed compression, Low-speed compression, and Low-speed rebound. - Fits both 29" and 27.5" wheels. Markings on the outer legs indicate the proper clamping point for the ideal axle-to-crown measurements depending on wheel size. The fork legs can be used with both wheel sizes. - Two Crown Options are available with this fork. The 47 offset is designed to work with 27.5" wheels and intended axle to crown. The 57 offset crown is designed for 29" wheels and axle to crown. For those looking to run the lower offset crown with 29" wheels please reference our fit document to see if your headtube length is compatible. - TSR Bleed Screws allow you to release excess pressures built up in the outer legs of your fork while riding keeping your fork smooth and supple all day long. Product Details: - 37mm 6000 Series Aluminum stanchions with aluminum legs - Externally adjustable high-speed compression, low-speed compression, and rebound - TPC+ Damper with HBO (Hydraulic Bottom Out) - TSR bleed buttons - Includes removable bolt-on fender - 2.6" max tire width - 223mm max rotor diameter - Wheel: 27.5" - Steerer (Stem/Race): straight (28.6/30) - Offset: 47mm - Travel: 203mm - Spring Type: Dorado Air w/ IVA - Damping: adjustable TPC - Adjustability: air volume, rebound, HS and LS compression - Brake Mount: disc only (PM-203) - Dropout: 20x110mm (Boost) - Axle-Crown: 582mm - Weight: 6.87lb (3120g)

Get Inverted. Back and better than ever the new Dorado Expert is ready to take on the gnarliest conditions mountain biking can provide. Whether you’re looking to cut seconds off the splits, lap the local park, or get sendy in the back hills of Utah the Dorado Expert has you covered. Featuring an all-new 37mm chassis, completely redesigned internals, and on-trail precision that only inverted forks can provide the new Dorado is your ticket to the best ride you’ve ever had. Key Features: - New 37mm chassis results in a massive increase in stiffness and ride quality. The new chassis is 20% stiffer compared to our former 36mm version - Inverted Design provides an incredibly smooth and consistent feel due to constant lubrication of the bushings and seals. The inverted design also provides a major increase in fore-aft stiffness compared to traditional forks while maintaining torsional compliance which provides more control to the rider over rough terrain. - The Dorado Air Spring system contains a unique balancing valve that equalizes the positive and negative air chambers during the air-fill process resulting in a consistent feel without any flat or dead spots. It also allows easy Travel Adjustability from 180 to 190 and 203mm without the need for any spare parts. - IVA (Incremental Volume Adjust) modifies the volume in the positive air chamber with self-contained spacers dictating the position of the IVA piston and your volume amount. - The new TPC+ Damper has increased oil volume and improved flow paths for improved bump compliance and increased consistency. TPC+ features two compression pistons, a hydraulic bottom out, and a spring-backed IFP for a smooth and predictable feel for every impact. Adjustments include; High-speed compression, Low-speed compression, and Low-speed rebound. - Fits both 29" and 27.5" wheels. Markings on the outer legs indicate the proper clamping point for ideal axle-to-crown measurements depending on wheel size. The fork legs can be used with both wheel sizes. - Two Crown Options are available with this fork. The 47 offset is designed to work with 27.5" wheels and intended axle to crown. The 57 offset crown is designed for 29" wheels and axle to crown. For those looking to run the lower offset crown with 29" wheels please reference our fit document to see if your headtube length is compatible. - TSR Bleed Screws allow you to release excess pressures built up in the outer legs of your fork while riding keeping your fork smooth and supple all day long. Product Details: - 37mm 6000 Series Aluminum stanchions with carbon fiber legs - Externally Adjustable: high-speed compression, low-speed compression, and rebound - Dorado air spring with IRT (Infinite Rate Tune) volume adjuster allows the rider to adjust mid-stroke support and bottom-out progressivity independent of initial spring rate - TPC+ Damper with HBO (Hydraulic Bottom Out) - TSR Bleeders - Includes removable bolt-on fender

36 E-Optimized Factory forks are made specifically for the rigors of E-Bikes with a stouter chassis and longer durability due to adding material to strengthen critical areas. The design also uses tuning originally done for Enduro use, which fits the needs of the E-MTB and overall E-Bike uses. - Genuine Kashima Coating on upper tubes - FIT GRIP2 Damper and FLOAT air spring - E-Bike Chassis - Lower Leg Bleeders and Bypass Channels - Floating axles for perfect alignment - Updated Crown Design saves up to 20 grams, and offers significant structural improvements

Own the mountain with the award-winning 36 Factory, featuring high- and low-speed rebound adjuster, improved compression damping and reduced friction for unmatched performance and adjustability. - Genuine Kashima Coating on upper tubes - FIT damper and FLOAT EVOL air spring - Low friction seals for improved performance - Lower Leg Bleeders and Bypass Channels - Floating axles for perfect alignment - Updated Crown Design saves up to 20 grams, and offers significant structural improvements

Own the mountain with the award-winning 36 Factory, featuring high- and low-speed rebound adjuster, improved compression damping and reduced friction for unmatched performance and adjustability. - Genuine Kashima Coating on upper tubes - FIT damper and FLOAT EVOL air spring - Low friction seals for improved performance - Lower Leg Bleeders and Bypass Channels - Floating axles for perfect alignment - Updated Crown Design saves up to 20 grams, and offers significant structural improvements

36 E-Optimized Factory forks are made specifically for the rigors of E-Bikes with a stouter chassis and longer durability due to adding material to strengthen critical areas. The design also uses tuning originally done for Enduro use, which fits the needs of the E-MTB and overall E-Bike uses. - Genuine Kashima Coating on upper tubes - FIT GRIP2 Damper and FLOAT air spring - E-Bike Chassis - Lower Leg Bleeders and Bypass Channels - Floating axles for perfect alignment

Own the mountain with the award-winning 36 Factory, featuring high- and low-speed rebound adjuster, improved compression damping and reduced friction for unmatched performance and adjustability. - Genuine Kashima Coating on upper tubes - FIT damper and FLOAT EVOL air spring - Low friction seals for improved performance - Lower Leg Bleeders and Bypass Channels - Floating axles for perfect alignment

- 35mm chassis with a focused all-mountain mindset - satisfyingly stiff, efficient and designed to eliminate as much weight as possible. - ButterCups block 20% of high frequency "trail chatter". Limiting these vibrations massively reduces hand and arm fatigue leaving you feeling fresh with more control. - Charger 3 features a new Internal Floating Piston (IFP) design with better fidelity, performance and truly independent adjustments without any "cross talk". - DebonAir+ is built to balance butter-like small bump feel, increased air volume, and higher overall ride height - Ultimate Bushing Package maximizes the fork's bushing overlap, reducing friction and creating the smoothest ride possible - Pressure Relief Valves eliminate unwanted air pressure build up in the lower leg caused by variations in altitude or temperature. - RockShox premium short fender included

The Cane Creek Helm MKII Air Suspension Fork features an upgraded damper design for increased support and control and a redesigned air spring that allows for increased air volume for better traction and suppleness. - D-Loc 15mm bolt-on thru-axle

The Cane Creek Helm MKII Coil Suspension Fork features an upgraded damper design for increased support and control. - Compression and midvalve circuit offer increased support and control - SKF oil seal head cartridge and wiper seals are low friction - Damping features include: high speed compression, low speed compression, low speed rebound - Adjustment options include: high speed compression (10 positions), low speed compression (17 positions), low speed rebound (10 positions), indexed travel adjust system, spring pre-load adjust - Lightweight coil spring - 55 lb Lightweight Coil Spring included from factory

The versatility of the Cane Creek HELM continues with the new HELM DJ. The new Cane Creek HELM DJ combines the proven performance, reliability and strength of the HELM MKII's chassis with a new short travel air spring optimized for Dirt Jumps, Dual Slalom and Street riding. Preset at 90mm travel and a 483mm axle to crown to accommodate a 26" wheel without changing the geometry of your dirt jump bicycle.

In 2019 Cane Creek launched their WS130 down country low travel fork, 4 years later they are paying homage to the WS130 by introducing an extremely limited run of their low travel modular fork, the Works Series Helm. The Works Series Helm is a robust, modular fork that equips riders looking for a fork in the 100-130mm travel range with the confidence to ride through tech or push up climbs. The Works Series Helm is available in 4 travel options: 100mm, 110mm, 120mm and 130mm options. Like Cane Creek’s Helm MKII, the Works Series can easily be travel adjusted in 10mm increments with just a few tools at home. Built with a stiffer chassis, the Works Series gives a smoother, more controlled ride. All of Cane Creek’s suspension products are hand-built in Western North Carolina and rigorously tested in the Pisgah National Forest.

Featuring 37mm stanchions and our Reverse Arch design the Mezzer Pro is the stiffest Enduro fork on the market… it’s also the lightest. How did we manage to accomplish this you ask? Well, it’s not hollow if that’s what you're wondering. In fact, this fork is loaded with technologies such as a fully sealed MC² damper, our proven Dorado air spring, and the life-changing IRT volume adjuster. What does all this mean? It means you no longer need to pick two, you can have the lightest, stiffest, and incredibly adjustable fork all at once. Key Features: - 37mm stanchions, Reverse Arch design, and Hexlock SL2 axle combined together result in ultimate stiffness - Originally developed for the Dorado down-hill fork, the Dorado Air Spring offers ultimate sensitivity featuring a self-equalizing negative air spring. When inflating the fork both the positive and negative air chambers are filled simultaneously equalizing the pressures to create an incredibly supple feel - IRT (Infinite Rate Tune) volume adjuster allows control over the mid-stroke support and bottom-out progressivity independent from the initial spring rate to independently tune small bump sensitivity and big-hit performance - Sealed MC² damper provides a range of blow-off thresholds to satisfy any requirement with separate high-speed and low-speed adjustments. Utilizing a bladder, our new sealed cartridge maintains damping consistency in the most severe riding conditions. - 140mm to 180mm internally adjustable travel in 10mm increments (travel spacers included) - 27.5” and 29” wheels - Integrated flexible fender can be installed/removed by three small screws threaded into the arch of the fork Product Details: - MC² bladder cartridge damper offers adjustable high-speed compression damping, low-speed compression damping - Expansion bladder with patent-pending blow-off valve compensates for oil displacement, with lower friction than a traditional internal floating piston - 37mm chassis with torsional stiffness up to 30% higher than similar forks from competitors - Dorado Air spring features an enlarged negative air chamber for linear initial stroke and reduced IRT volume for progressive end stroke - Internally adjustable travel from 180mm to 140mm

The 34 Step-Cast Factory is the choice for riders who want an all-round fork that performs in a vast range of applications: lightweight for climbs and highly capable for demanding terrain with enough travel to instill confidence when the trail gets rough. Weight savings are attributed to external lower casting steps, hollow lower section, and shortened shaft lengths. - Step-Cast chassis - Genuine Kashima Coating on upper tubes - FIT4 damper and FLOAT EVOL air spring - Dedicated air spring and damper tune are specific for this travel range, with a lighter tune at mid and higher velocities

The 34 Step-Cast Factory is the choice for riders who want an all-round fork that performs in a vast range of applications: lightweight for climbs and highly capable for demanding terrain with enough travel to instill confidence when the trail gets rough. Weight savings are attributed to external lower casting steps, hollow lower section, and shortened shaft lengths. - Step-Cast chassis - Genuine Kashima Coating on upper tubes - FIT4 damper and FLOAT EVOL air spring - Dedicated air spring and damper tune are specific for this travel range, with a lighter tune at mid and higher velocities - Kabolt Thru Axle

Own the mountain with the award-winning 36 Factory, featuring high- and low-speed rebound adjuster, improved compression damping and reduced friction for unmatched performance and adjustability. - Genuine Kashima Coating on upper tubes - FIT damper and FLOAT EVOL air spring - Low friction seals for improved performance - Lower Leg Bleeders and Bypass Channels - Floating axles for perfect alignment - Updated Crown Design saves up to 20 grams, and offers significant structural improvements

Riding SID Ultimate means every detail is considered. Packed in an all new chassis, the new Charger Race Day damper is the lightest yet. Perfectly balanced for the speed needs of XC. - 35mm chassis is the perfect blend of lightweight and stiffness for the modern XC bike - Charger Race Day Damper - Rockshox's lightest production damper with rock-solid lockout - DebonAir air spring is tuned specific to meet the demands of XC and maintains a higher ride height for increased confidence and control - Ultra-low friction SKF wiper seals provide long-lasting fork performance and improve overall suspension feel - Maxima Plush damping fluid reduces friction and silences damper noise - Machined/anodized crown - Ultimate foil graphics package - OneLoc Remote Specifications: - Wheel Size: 29" - Positive Spring: Air - Brake Type: Post Mount 180 - Crown Race: 40 - External Adjustments: Lockout Threshold, Rebound Damping - Negative Spring: Air - Stanchion Diameter: 35 - Steerer Type: Tapered - Maximum Tire Width: 66 - Offset: 44 - Steerer Tube Length (mm): 230 - Color: Gloss Black - Front Axle: 15mm Thru x 110mm - S.H.I.S. Stem Clamp Diameter: 28.6 - Travel (mm): 120 - Axle to Crown Length: 531 - Lockout Switch: Handlebar - Cable

Own the mountain with the award-winning 36 Factory, featuring high- and low-speed rebound adjuster, improved compression damping and reduced friction for unmatched performance and adjustability. - Genuine Kashima Coating on upper tubes - FIT damper and FLOAT EVOL air spring - Low friction seals for improved performance - Lower Leg Bleeders and Bypass Channels - Floating axles for perfect alignment

- 35mm chassis at home on the trail - stiff, playful and light, really light - ButterCups block 20% of high frequency “trail chatter”. Limiting these vibrations massively reduces hand and arm fatigue leaving you feeling fresh with more control. - Charger 3 features a new Internal Floating Piston (IFP) design with better fidelity, performance and truly independent adjustments without any "cross talk". - DebonAir+ is built to balance butter-like small bump feel, increased air volume, and higher overall ride height - Ultimate Bushing Package maximizes the fork’s bushing overlap, reducing friction and creating the smoothest ride possible - Pressure Relief Valves eliminate unwanted air pressure build up in the lower leg caused by variations in altitude or temperature. - RockShox premium short fender included

Featuring 37mm stanchions and our Reverse Arch design the Mezzer Pro is the stiffest Enduro fork on the market… it’s also the lightest. How did we manage to accomplish this you ask? Well, it’s not hollow if that’s what you're wondering. In fact, this fork is loaded with technologies such as a fully sealed MC² damper, our proven Dorado air spring, and the life-changing IRT volume adjuster. What does all this mean? It means you no longer need to pick two, you can have the lightest, stiffest, and incredibly adjustable fork all at once. Key Features: - 37mm stanchions, Reverse Arch design, and Hexlock SL2 axle combined together result in ultimate stiffness - Originally developed for the Dorado down-hill fork, the Dorado Air Spring offers ultimate sensitivity featuring a self-equalizing negative air spring. When inflating the fork both the positive and negative air chambers are filled simultaneously equalizing the pressures to create an incredibly supple feel - IRT (Infinite Rate Tune) volume adjuster allows control over the mid-stroke support and bottom-out progressivity independent from the initial spring rate to independently tune small bump sensitivity and big-hit performance - Sealed MC² damper provides a range of blow-off thresholds to satisfy any requirement with separate high-speed and low-speed adjustments. Utilizing a bladder, our new sealed cartridge maintains damping consistency in the most severe riding conditions. •140mm to 180mm internally adjustable travel in 10mm increments (travel spacers included) •27.5” and 29” wheels •Integrated flexible fender can be installed/removed by three small screws threaded into the arch of the fork Product Details: - 37mm stanchions Reverse-Arch design and Hexlock SL2 axle for the ultimate stiffness - Fully adjustable IRT air spring to fine-tune ride feel - Sealed MC2 damper provides a range of blow-off thresholds to satisfy any requirement with separate high-speed and low-speed adjustments - 140mm to 180mm internally adjustable travel in 10mm increments (travel spacers included) - Integrated flexible fender can be installed/removed by three small screws threaded into the arch of the fork

- All Mountain/Enduro fork with 35mm stanchions - Twin-tube damper with low-pressure IFP and air spring (positive and negative air chambers), internal travel adjustment (120-160mm of travel in 5mm increments*) easily adjustable, and all parts included - ChocoLUXE Internals - ChocoLUXE is a proprietary material utilized in the damper plug, damper seal, damper IFP, and damper support. - Norglide Bushings—Norglide Bushings from Saint Gobain are metal-reinforced, self-lubricating bushings with a layer of a low friction PTFE compound. - Damper adjustments include air spring pressure, 8-position compression, ramp control (air spring ending stroke feel), and rebound - Ramp Control—'on the fly' ending stroke compression adjustment - 74mm post-mount 180mm disc brake only - Boost 15x110mm QR thru-axle - Every MRP fork is built in the MRP factory and dyno verified to ensure the highest level of quality and ensure long-term reliability - 4.2lb (1950g)